Understanding the fuel is key to maintaining your car performance. This is especially applied to the 2008 Scion xB type, widely known for its excessive oil usage.
Hence, this post will help you comprehend this automotive aspect more by providing comprehensive insights. Stay tuned!
What Are The 2008 Scion XB Oil Types?
There are two common kinds of Scion xB oil, SAE 5W-20 and SAE 0W-20. The SAE 5W-20 is recommended by the Scion brand under low temperatures, while the latter should be used during warm or moderate days.
The difference between these two engine oils lies in the numbers or letters printed on the gasoline label, which entail helpful information about the fuel’s characteristics and efficiency.
Below are some important symbols that you should remember:
- The first number shows the viscosity level under 0 degrees Fahrenheit.
- The letter W indicates the great oil performance in cold weather.
- The second number denotes the fuel’s thickness level at 212 degrees Fahrenheit.
What Is The 2008 Scion xB Engine Oil Capacity?
This oil type, often powered by the 4-cyl engine, records a usage total of between 4.3 and 4.5 liters.
If used in larger machines, the fuel amount can reach up to five or even six quarts of motor oil, depending on your vehicle.
Moreover, it is advisable for you to differentiate two terms: engine displacement and oil capacity.
The former is defined as a measurement of the oil volume your vehicle cylinder may consume, while the latter is indicative of the oil amount required during each fuel change.
How Often Do You Change The 2008 Scion XB Oil?
You are recommended to change the oil within the distance between 3000 and 5000 miles. Or if you have driven a lot, a six-month period may be more suitable.
However, the 2008 Scion xB vehicle has a bad reputation for excessive oil consumption due to a defective car piston.
Accordingly, some problems of shortened engine life and engine sludge are likely to arise if you don’t refuel the engine promptly.
Here are some signs that notify you of the low oil level:
- Unusual smells, such as a smoky or burning oil smell through vents.
- The reduced performance of your automobile.
- The triggered check engine light.
- Unusual sounds, such as humping or clicking noise while you don’t disengage the clutch.
How To Change The 2008 Scion XB Oil?
Below is an all-inclusive guideline for you to consider:
- Step 1: You need to loosen the lug nuts on your car wheel. If they are surrounded by a steel cover, you should use a wrench or iron to remove this protective layer.
- Step 2: Afterward, you pry lug nuts and bolts off the wheel. Then, you unscrew it off the hub and place it nearby.
- Step 3: Use a jack positioned under a vertical frame underneath your automobile to raise it. Remember to heighten it until the wheel is far from the ground, at a couple of inches.
- Step 4: Lie down under your car, and you will spot three retainers on the flap. Remove them by using force to separate the push pin.
- Step 5: You are required to search for an oil drain, which lies at the back corner of your motor oil pan. Place a container below.
- Step 6: Use a wrench to loosen the drain plug and continue by manually twisting until it is off. Then, the oil will start to drain.
- Step 7: It’s time you take the old gasket out from the oil drain plug by straightening it up before installing a new one.
- Step 8: When the oil only falls in small drops, use a towel to clean the surrounding area. After that, you reinstall a new drain plug in the firm position by tightening it.
- Step 9: Locate oil filters and place an oil pan right below them. When you finish, use a screwdriver to loosen by twisting it a couple of turns until it is off.
- Step 10: Prepare a new filter and spread clean oil on its surface and rubber gasket. Place it over the threads and manually twist it to tighten.
- Step 11: Open the car hood and pull it upward. Use a release latch and rods to keep it opening stationary.
- Step 12: Pinpoint the location of an oil filler cap, which lies on the engine’s passenger side. Use your hand to force it clockwise until you can remove it from the valve.
- Step 13: This step requires you to pour new oil into the engine via a funnel. About 4.3 to 4.5 quarts of oil are sufficient for an automobile to run efficiently.
- Step 14: Grab a yellow handle to pull the dipstick out from the valve cover. Then, you carefully clean before reinserting it to reap an accurate oil level reading you have just poured. Reinstall it and the cap afterward.
- Step 15: Close the hood by pressing two rods and putting them back into the clip. Don’t forget your funnel.
- Step 16: Make a replacement of the push and three retainers before positioning them in the correct holes, respectively.
- Step 17: Attach the wheel to the hub again and use your hand to make it tight. Avoid placing it off-center, as dangerous scenarios stemming from this practice may follow.
- Step 18: Put lug holts back onto the wheel. Use a wrench or tire iron to tighten them evenly.
- Step 19: Lower your car gradually by pressing the jack down. Remove it when your automobile safely lands on the ground.
- Step 20: This step is optional. If a steel cover protects your wheel, place it back around the wheel.
- Step 21: Before you drive, you should start the engine and let it be for a while, allowing the new oil to well-circulate through the mechanism parts.
The Bottom Line
We hope this article helps you learn about the 2008 Scion xB oil type.
Needless to say, oil is of tremendous importance to engines by protecting them from wear and tear thanks to its lubricating function.
Therefore, you should keep track of your car’s oil condition frequently to avert unexpected problems.
Thank you for supporting our website!