Clutch Goes To Floor Without Resistance- Top Reason And Fixes!

The clutch controls the car transmission, which is one of the most important parts in maintaining the vehicle’s operation.

Like the brake pedal, press your foot, and you can exercise arbitrary speed control while feeling an invisible resistance under your foot, preventing your foot from hitting the actual floorboard.

But the problem suddenly occurred one day! Have you noticed that no matter what you do, your clutch goes to floor without resistance

Don’t worry because this post contains all the information about the causes, telltale signs, and the most effective treatment guide to getting your car back in tip-top shape.

Clutch Goes To Floor Without Resistance – Common Signs

clutch goes to floor without resistance
Clutch Has No Resistance

Short answer: The life of a clutch will range from 50,000 miles to 100,000 miles depending on the vehicle and the driver’s maintenance.

If your car’s clutch has no resistance in combination with the signs below, it sends you a distress signal!

Higher Bite/Catch Point

The clutch grip point (bite point) is where the clutch transmits power to the gearbox, creating the driving force for the vehicle to perform the gear shift.

Its change is highly dependent on the product’s degree of wear and damage.

A higher-than-normal clutch grip is the most obvious sign that the clutch has a problem and needs to be replaced promptly.

Burning Odors

The burning smell emanating from engine parts is never a problem to be taken lightly, as it signals that the component is in serious condition.

If the clutch emits a strange odor, it signals a clutch slip. A slipping clutch is often accompanied by thermal overload, greatly hindering shifting.

Shifting the Gears Problems

A clutch slip means no power can be sent to the manual transmission. Instead, it will be “contained” inside the engine, making it difficult to shift into gear.

In the most severe cases, this problem can result in the driver being unable to shift into gear despite being on the highway.

Therefore, contact a repair center whenever the clutch shows failure or the vehicle has problems while shifting gears.

Hesitation When Accelerating

When the required force is not received, the transmission system cannot operate.

The wheels can’t work properly (or even can’t turn), resulting in your vehicle’s tendency to hesitate even when traveling on flat roads or accelerating after changing gears.

Strange Noises

Are there some strange sounds like a squeak from the clutch every time you try to shift gears? That is a sign that the grinding equipment has slipped and needs immediate repair.

If a sound comes from the clutch pedal every time the driver presses and releases it, it is simply having a problem due to a long period of operation.

Instead of skipping it, please take it to the auto shop to regain the most comfortable and quiet driving experience.

Clutch Not Working No Resistance- Main Reasons

clutch not working no resistance
What The Causes Of Clutch Not Working No Resistance

The abnormal operation of some components connected to the clutch is the leading cause of the clutch operating without any resistance.

If you’re wondering what they are, we have the answer below!

Broken Clutch Cable

Cars can only complete gear shifts through the clutch cable path. A broken clutch cable is a leading cause of the clutch pedal hitting the floor, especially in older vehicles.

Luckily, replace the cable, and you can engage the clutch and shift gears normally.

Low Fluid

If your vehicle has a hydraulic clutch, the main cause for the clutch pedal going to the floor is likely to be lower than specified fluid levels in the master or auxiliary cylinders.

Your concern is correct if a visual inspection of the liquid reservoir shows that the liquid level is below the “full” line!

So, why is the oil level inside the reservoir lower than normal?

Please pay attention to the lock first, as its deterioration over time or leakage can cause the hydraulic point of the process to be low.

Once the auxiliary cylinder fails, you cannot control the oil level until it runs out.

Defective flywheel control valves can also cause a loss when clutch fluid flows into the handbrake, hindering deceleration.

However, pay attention because its markings are not so obvious if you only check the fuel tank and dashboard!

Bad Connector Rod

The clutch cable connects the bearing, fork, and even a small rod. Without this connector rod, the cable cannot be fixed to the fork, resulting in the pedal falling to the floor.

Clutch Master Cylinder Problem

A damaged clutch master cylinder can be caused by brake fluid leaking from the inner seals, causing the fluid level to drop drastically.

This problem is quite difficult to recognize because sometimes you will not see or see liquid on the clutch pedal, the back of the engine, and the firewall depending on certain circumstances.

Bad Clutch Slave Cylinder

The auxiliary cylinder is less prone to failure than the master cylinder, but you can’t ignore it either!

The symptoms and their causes are quite similar – the seals are loose and leaky, causing the liquid level to drop further and further.

What To Do If My Clutch Pedal Has No Resistance?

clutch has no resistance
How To Fix Clutch Pedal Has No Resistance

Any problems related to the clutch not working properly have reasonable solutions. If you don’t have any ideas yet, check out our two steps below!

Step 1: Repair The Ignition Coil

All the above causes lead to a faulty ignition coil, causing clutch failure. Therefore, you will need to check this unit before continuing to trace other sources of problems.

Clutch systems usually appear in one of two power units: the gear and stop units. Check where it is mounted and replace it if it shows deterioration.

But remember, this is a high-risk job, so do it under the guidance of a professional.

Step 2: Contact A Professional Mechanic

If replacing the ignition coil still doesn’t save the situation, chances are the problem is more serious than you think.

Because riding in a vehicle with a clutch problem is potentially dangerous, it’s best to contact your nearest auto repair center to seek help.


How Much Does It Cost To Fix The Clutch Going To Floor?

The cost of this problem is very much related to the part that caused the clutch to go to the floor.

Typically, the driver will have to replace the entire clutch at a cost that ranges from $1,000 to $2,500, depending on your local repair center’s policy.

Is It Safe To Drive If My clutch goes to the floor?

A faulty gearbox disrupts the operation of the gearbox and engine, making it impossible for the driver to control the car’s ability to decelerate at will.

Therefore, you should contact the nearest repair center and report the situation to know the next solution.

How To Avoid Clutch Going To The Floor? 

Driving carefully and regularly maintaining all the components inside the car is the most effective solution to prevent the clutch from going to the floor.

Besides, always use good quality cable systems whenever this part needs to be replaced, helping minimize clutch-related problems.

Our Final Thought

The clutch can be considered the soul of a car because it is one of the essential parts.

However, over time, any driver will notice the signs of clutch failure, leading to the phenomenon of “clutch goes to floor without resistance.”

Through this article, we hope you have a more comprehensive insight into this part, the causes, the best signs, and how to handle the incident if it happens while on the road.

Leave a comment if you have any questions, and we will respond soon!

Leave a Comment